DPA 4015A Stereo Pair with Clips and Windscreens in Peli Case
Kontakt os på +45 3120 7021 eller info@nordicproaudio.com
DPA 4015A Wide Cardioid Stereo Pair
A complete Stereo Pair with two carefully factory-matched 4015 Wide Cardioid Microphones. Even though the standard tolerances on our recording mic series is extremely low, a stereo match is even closer. These mics are matched within ±1 dBon both frequency response and sensitivity. The pair comes with two 4015 mics, clips and windscreens in a Peli™ Case.
Our wide cardioid microphones are capable of handling extremely high sound pressure levels before clipping occurs. The 4015A Wide Cardioid Microphone even includes a 20 dB pad switch in the center of the XLR connector to prevent overloading of the mic amplifier.
Sometimes a conventional cardioid pattern just isn’t quite open enough. Recording orchestras or other ensembles sometimes requires a compromise between blending in the room reverberation and a more precise localization. When recording instruments with complex radiation patterns, the wide cardioid (also known as hemispheric) design covers a greater sound angle and is an excellent choice. This is the often ideal mic for recording grand piano, guitar, marimba, and percussion, or as a spot mic for groups in a symphony orchestra. Likewise, it is an excellent speech, dubbing, or vocal mic as its enhanced richness on the bass end nicely compliments many voices.
The foam design in the heavy-duty transportation box allows for fast and easy exchange of the microphone/accessory inlays.
- 2x DPA 4015A Wide Cardioid Microphones
- 2x Foam Windscreens
- 2x DPA Microphone Clips
- 1x Peli Case
| Directional Pattern: | Wide cardioid |
|---|---|
| Principle of operation: | Pressure gradient |
| Cartridge type: | Pre-polarized condenser |
| Frequency response: | 20 Hz - 20 kHz |
| Dynamic range: | Typ. 121 dB |
| Effective frequency range, ±2 dB, at 60 cm (23.6 in): | 40 Hz - 20 kHz |
| Sensitivity, nominal, ±2 dB at 1 kHz: | 10 mV/Pa; -40 dB re. 1 V/Pa |
| Equivalent noise level, A-weighted: | Typ. 18 dB(A) re. 20 µPa (max. 20 dB(A)) |
| Equivalent noise level, ITU-R BS.468-4: | Typ. 25 dB (correct with the attenuator in 0 dB or -20 dB setting) |
| Distortion, THD < 1%: | 136 dB SPL RMS, 139 dB SPL peak |
| Max. SPL, THD 10%: | 159 dB SPL peak |
| Switchable attenuator, filters etc.: | 0 dB / -20 dB |
| Rated output impedance: | 200 Ω |
| Minimum load impedance: | 2 kΩ |
| Cable drive capability: | 100 m (328 ft) |
| Output balance principle: | Impedance balancing with Active Drive |
| Common mode rejection ratio (CMRR): | > 60 dB |
| Power supply (for full performance): | P48 (Phantom Power) |
| Current consumption: | 2.8 mA |
| Maximum output voltage, RMS: | > 5 V |
| Polarity: | +V at pin 2 for positive sound pressure |
| Matching tolerance (frequency response and sensitivity): | ±1 dB |
| Phase deviation for kit: | < 10° |
| Microphone diameter: | 19 mm (0.75 in) |
| Capsule diameter: | 19 mm (0.75 in) |
| Microphone length: | 170 mm (6.7 in) |
| Temperature range: | -40°C to 45°C (-40°F to 113°F) |
| Relative humidity (RH): | Up to 90% |