DPA 4098 CORE Supercardioid Tabletop Mic, 43 cm (17 in), Black, XLR, P48
Supercardioid Tabletop Microphones
A complete, supercardioid tabletop microphone solution, which is ideal for either permanently affixing to or temporarily placed on a table in conference venues, meeting rooms and board rooms.
- Outstanding audio quality
- Slim, elegant Scandinavian design
- Highly directional – very isolated
- High rejection of radio frequency interference
- Meets the needs of architects, AV consultants, system integrators and installing electricians
This solution can be scaled up as needed. In smaller rooms you might only need one microphone to capture the best sound. In larger settings, you can use multiple mics to ensure each area of the room is completely covered. The best audio quality is obtained in a one-to-one solution – one microphone position close to one speaker.
Speech intelligibility - low noise
With very low noise and a high sensitivity, our ceiling and tabletop microphones offer the most clear, transparent, and natural sound available on the small footprint mic market. They ensure maximum speech intelligibility regardless of the acoustical environment. With a linear response, low distortion and an extremely large dynamic range, they sound great in any environment.
The Microphone Base is made specifically to work with the 4098 CORE Supercardioid Podium Microphone. It has an elegant yet unobtrusive design with a white, non-reflective surface and integrated shock mount. The audio cables are an integral part of the Microphone Base unit.
The Microphone Base fits most electrical back boxes and secures ease of installation. Furthermore, the great off-axis response and the physics of sound level vs distance, makes it possible to cover a small to mid-size room with only one or a few microphones. Read more about microphones in installed systems.
DPA 4098 Frequency Response:
Typical on and off-axis response of a DPA 4098
DPA 4098 Polar Pattern:
Typical directional characteristics of DPA 4098
- 1x DPA 4098 CORE Supercardioid Tabletop Mic
- 1x Foam Windscreen
- 1x Microphone Base
|Principle of operation:||Pressure gradient|
|Cartridge type:||Pre-polarized condenser|
|Frequency response:||20 Hz - 20 kHz|
|Dynamic range:||Typ. 110 dB|
|Effective frequency range ±2 dB, at 20 cm (7.9 in):||MicroDot: 80 Hz - 15 kHz with 3 dB soft boost at 8-15 kHz|
XLR-3M: 100 Hz - 15 kHz with 3 dB soft boost at 8-15 kHz and permanent 2nd order low-cut filter at 80 Hz
|Sensitivity, nominal, ±3 dB at 1 kHz:||16 mV/Pa; -36 dB re. 1 V/Pa|
|Equivalent noise level, A-weighted:||Typ. 23 dB(A) re. 20 µPa (max. 26 dB(A))|
|Equivalent noise level, ITU-R BS.468-4:||Typ. 35 dB (max. 38 dB)|
|Distortion, THD < 1%:||130 dB SPL RMS, 133 dB SPL peak|
|Max. SPL, THD 10%:||135 dB SPL peak|
|Rated output impedance:||From MicroDot: 30 - 40 Ω. From XLR connector or DAD6001-BC XLR Adapter: 100 Ω|
|Minimum load impedance:||2 kΩ|
|Cable drive capability:||MicroDot: Up to 300 m (984 ft) with DAD6001-BC XLR Adapter|
XLR-3M: Up to 100 m (328 ft)
|Output balance principle:||Signal balanced with XLR connector or DAD6001-BC XLR Adapter|
|Common mode rejection ratio (CMRR):||> 60 dB from 50 Hz to 15 kHz with DAD6001-BC XLR Adapter|
|Power supply (for full performance):||MicroDot: Min. 5 V to max. 10 V through DPA adapter for wireless systems or|
P48 (Phantom Power) with DAD6001-BC XLR adapter
XLR-3M: P48 (Phantom Power)
|Current consumption:||Typ. 1.5 mA (microphone). 3.5 mA with DAD6001-BC XLR Adapter|
|Polarity:||+V at MicroDot pin for positive sound pressure (and pin 2 on XLR connector or DAD6001-BC XLR adapter)|
|Microphone diameter:||5.7 mm (0.22 in)|
|Microphone length:||Microdot: 16 cm (6 in), 28 cm (11 in), 43 cm (17 in), 77 cm (30 in), 122 cm (48 in)|
XLR-3M: 20 cm (8 in), 32 cm (13 in), 47 cm (18 in), 77 cm (30 in), 122 cm (48 in).
|Temperature range:||-40°C to 45°C (-40°F to 113°F)|
|Relative humidity (RH):||Up to 90%|