DPA 4098 CORE Supercardioid Mic, Black, MicroDot, 28 cm (11 in) Boom, top and bottom Gooseneck
Please contact us on +45 3120 7021 or info@nordicproaudio.com
Speech intelligibility - low noise
DPA gooseneck microphones have quickly become a very popular choice for podium mics as well as for conference room usage as either tabletop or ceiling mount.
- With MicroDot Connector
- Choose between black or white
- Outstanding audio quality
- Wireless podium mic capability
- Highly directional – very isolated
- High rejection of radio frequency interference
- Sleek Scandinavian design
With very low noise and a high sensitivity, 4098 CORE Supercardioid Microphones offer the most clear, transparent, and natural sound available on the miniature mic market. The mics are capable of handling extremely high SPL before clipping, which allows the mic to deliver high speech intelligibility even when the speaker gets excited and starts to speak VERY loudly. With a linear response, low distortion and an extremely large dynamic range, these mics sound great no matter how challenging the environment.
CORE by DPA technology has been added to the 4098 microphone, lifting sound quality even more, just like all of the other products using CORE technology. The 4098s dynamic range has been increased by 8 dB, so that the 1% THD is lifted significantly to 133 dB.
In addition, speaking into the side (off-axis) of the microphone doesn’t make the audio sound worse, it just drops the level of your voice.
DPA 4098 Frequency Response:
Typical on and off-axis response of a DPA 4098
DPA 4098 Polar Pattern:
Typical directional characteristics of DPA 4098
- 1x DPA 4098 CORE Gooseneck Supercardioid Microphone, Microdot
- 1x Foam Windscreen
Directional Pattern: | Supercardioid |
---|---|
Principle of operation: | Pressure gradient |
Cartridge type: | Pre-polarized condenser |
Frequency response: | 20 Hz - 20 kHz |
Dynamic range: | Typ. 110 dB |
Color: | Black |
Length: | 28 cm |
Connector: | MicroDot |
Effective frequency range ±2 dB, at 20 cm (7.9 in): | MicroDot: 80 Hz - 15 kHz with 3 dB soft boost at 8-15 kHz XLR-3M: 100 Hz - 15 kHz with 3 dB soft boost at 8-15 kHz and permanent 2nd order low-cut filter at 80 Hz |
Sensitivity, nominal, ±3 dB at 1 kHz: | 16 mV/Pa; -36 dB re. 1 V/Pa |
Equivalent noise level, A-weighted: | Typ. 23 dB(A) re. 20 µPa (max. 26 dB(A)) |
Equivalent noise level, ITU-R BS.468-4: | Typ. 35 dB (max. 38 dB) |
Distortion, THD < 1%: | 130 dB SPL RMS, 133 dB SPL peak |
Max. SPL, THD 10%: | 135 dB SPL peak |
Minimum load impedance: | 2 kΩ |
Rated output impedance: | From MicroDot: 30 - 40 Ω. From XLR connector or DAD6001-BC XLR Adapter: 100 Ω |
Cable drive capability: | MicroDot: Up to 300 m (984 ft) with DAD6001-BC XLR Adapter XLR-3M: Up to 100 m (328 ft) |
Output balance principle: | Signal balanced with XLR connector or DAD6001-BC XLR Adapter |
Common mode rejection ratio (CMRR): | > 60 dB from 50 Hz to 15 kHz with DAD6001-BC XLR Adapter |
Power supply (for full performance): | MicroDot: Min. 5 V to max. 10 V through DPA adapter for wireless systems or P48 (Phantom Power) with DAD6001-BC XLR adapter XLR-3M: P48 (Phantom Power) |
Current consumption: | Typ. 1.5 mA (microphone). 3.5 mA with DAD6001-BC XLR Adapter |
Polarity: | +V at MicroDot pin for positive sound pressure (and pin 2 on XLR connector or DAD6001-BC XLR adapter) |
Microphone diameter: | 5.7 mm (0.22 in) |
Microphone length: | Microdot: 16 cm (6 in), 28 cm (11 in), 43 cm (17 in), 77 cm (30 in), 122 cm (48 in) XLR-3M: 20 cm (8 in), 32 cm (13 in), 47 cm (18 in), 77 cm (30 in), 122 cm (48 in). |
Temperature range: | -40°C to 45°C (-40°F to 113°F) |
Relative humidity (RH): | Up to 90% |