DPA 4071 CORE ENG/EFP Microphone Kit
Please contact us on +45 3120 7021 or info@nordicproaudio.com
Complete ENG/EFP kit with mics and accessories
This microphone kit is configured to include the mic and accessories necessary for electronic newsgathering and electronic field production.
It contains a 4071 Omnidirectional Microphone, Presence Boost with our reinforced cable relief (pre-equalized for speech clarity). This provides the final tonal adjustment needed for going directly on air or to tape without editing. The combination of the mic and the XLR adapter makes voices more distinguishable and improves speech intelligibility and definition.
This mic is an outstanding speech and vocal mic. It makes voice heard and intelligible. It is also resistant to moisture, extreme temperature change and humidity.
When recording voices from mic placement on a performer's body, no frequency below 100 Hz is attractive. For this reason, an acoustical low-cut has been incorporated in the mic capsule so the built-in preamplifier (and the wireless system) will have much larger headroom. Furthermore, it removes distant rumbling from cars, trains, airplanes, etc.
Another equally important consideration is that when placing a microphone on the body, especially on the chest, the frequency range of the consonants is damped, resulting in poor intelligibility. The 4071 Omnidirectional Microphone, Presence Boost has a built-in boost to compensate for this loss. Especially for ENG work, this mic is perfect because almost no ENG mixer leaves any possibility for a compensation of this kind.
The ENG / EFP Microphone Kit is delivered in a sturdy case with a transparent lid. Inside there is room for the microphone, one or more adapters and various microphone concealment fixtures.
- 1x DPA 4071 CORE Omni Mic, Presence Boost
- 1x MikroDot adapter for XLR
- 1x Double Holder
- 1x DPA Curved Clip
- 8x Foam Windscreens, Color mix
- 1x Fur Windscreen
- 1x Miniature Mesh
| Directional Pattern: | Omnidirectional |
|---|---|
| Principle of operation: | Pressure gradient |
| Cartridge type: | Pre-polarized condenser |
| Frequency response: | 20 Hz - 20 kHz |
| Dynamic range: | Typ. 111 dB |
| Effective frequency range ±2 dB: | 100 Hz - 15 kHz with typ. 5 dB soft boost at 4 - 6 kHz |
| Sensitivity, nominal, ±3 dB at 1 kHz: | 6 mV/Pa; -44 dB re. 1 V/Pa |
| Equivalent noise level, A-weighted: | Typ. 26 dB(A) re. 20 µPa (max. 28 dB(A)) |
| Equivalent noise level, ITU-R BS.468-4: | Typ. 38 dB (max. 40 dB) |
| Distortion, THD < 1%: | 134 dB SPL RMS, 137 dB SPL peak |
| Max. SPL, THD 10%: | 144 dB SPL peak |
| Rated output impedance: | 30 - 40 Ω |
| Cable drive capability: | Up to 300 m (984 ft) with DAD6001-BC XLR adapter |
| Power supply (for full performance): | For wireless systems Min. 5 V - max. 10 V through DPA adapter With DAD6001-BC: P48 (Phantom Power). Will work from 12 V |
| Current consumption: | Typ. 1.5 mA (microphone). 3.5 mA with DAD6001-BC XLR Adapter |
| Polarity: | Positively increasing sound pressure produces positive going voltage on MicroDot pin |
| Microphone diameter: | 5.4 mm (0.21 in) |
| Microphone length: | 17 mm (0.67 in) |
| Cable length: | 1.8 m (5.9 ft) |
| Temperature range: | -40°C to 45°C (-40°F to 113°F) |
| Relative humidity (RH): | Up to 90% |