DPA 4060 Omni Boundary Layer Mic, Silver and Black, XLR
;)
;)
Please contact us on +45 3120 7021 or info@nordicproaudio.com
Optimized to boost speech intelligibility
This mic solution is ideal for use in boardrooms, conference facilities, and courtrooms. It is also a great solution for teleconferencing and other applications where excellent vocal pickup is required.
The 4060 Omni Boundary Layer Mic is a transducer designed to work under optimum conditions when placed on a tabletop, but it also performs well on any other hard, flat surface that reflects sound.
- Ideal for use in boardrooms and conference facilities
- Sleek low profile Scandinavian Design
- Optimized to boost speech intelligibility
- Modular adapter system fits most professional wireless systems
The microphone is a pre-polarized omnidirectional miniature condenser microphone with a 5.4 mm (0.2 in) vertical diaphragm. The mic body consists of a central rubber disc that holds the mic element mounted in an elegant stainless steel base.
Easy Mounting
The 4060 Omni Boundary Layer Mic can be very easily placed in essentially any position on the surface of a table, even close to the edge. Users will benefit from the special characteristics of the surrounding sound field on which the mic is mounted: a 6 dB gain of direct sound and only a 3 dB gain of the diffuse sound. The sound captured has both greater clarity, especially at high frequencies, and speech intelligibility compared to sound captured above the surface.
The 4060 Omni Boundary Layer Mic uses CORE by DPA technology and features two M5 threaded holes on the backside of the unit, which means that it can be permanently affixed to the table. Furthermore, the slim cable can be run either through or along the table.
Adapter system gives you flexibility
A wide range of connection adapters and power supplies makes it possible to use the 4060 Omni Boundary Layer Mic with any microphone input. It is delivered with a DAD6001 XLR Adapter, but as the supplied cable is terminated with a DPA MicroDot connector this microphone can be connected to a wireless system via the flexible adapter system.
BLM 4060 Frequency Response
Typical on and off-axis response of a BLM4060
- 1x 4060 Omni Boundary Layer Mic
| Directional Pattern: | Omnidirectional, hemisphere |
|---|---|
| Principle of operation: | Pressure gradient |
| Cartridge type: | Pre-polarized condenser |
| Frequency response: | 20 Hz - 20 kHz |
| Dynamic range: | Typ. 100 dB |
| Effective frequency range ±2 dB: | 20 Hz - 14 kHz, with 7 dB soft boost at 8 kHz |
| Sensitivity, nominal, ±3 dB at 1 kHz: | 20 mV/Pa; -34 dB re. 1 V/Pa |
| Equivalent noise level, A-weighted: | Typ. 23 dB(A) re. 20 µPa (max. 26 dB(A)) |
| Equivalent noise level, ITU-R BS.468-4: | Typ. 35 dB (max. 38 dB) |
| Distortion, THD < 1%: | 120 dB SPL RMS, 123 dB SPL peak |
| Max. SPL, THD 10%: | 134 dB SPL peak |
| Rated output impedance: | From MicroDot: 30 - 40 Ω. From DAD6001-BC: 100 Ω |
| Cable drive capability: | Up to 300 m (984 ft) with DAD6001-BC XLR adapter |
| Power supply (for full performance): | For wireless systems Min. 5 V - max. 10 V through DPA adapter With DAD6001-BC: P48 (Phantom Power). Will work from 12 V |
| Current consumption: | Typ. 1.5 mA (microphone). 3.5 mA with DAD6001-BC XLR Adapter |
| Polarity: | Positively increasing sound pressure produces positive-going voltage at MicroDot pin (and pin 2 on DAD6001-BC XLR adapter) |
| Sensitivity selection tolerance (at 1 kHz): | ±1.5 dB |
| Weight: | 240 g (8.5 oz) excl. Cable |
| Microphone diameter: | 12 mm (0.47 in) |
| Microphone length: | 100 mm (4 in) |
| Cable length: | 3 m (10 ft) |
| Cable color: | Black |
| Cable diameter: | 1.6 mm (0.06 in) |
| Temperature range: | -40°C to 45°C (-40°F to 113°F) |
| Relative humidity (RH): | Up to 90% |