DPA 4006A Stereo Kit
;)
;)
Please contact us on +45 3120 7021 or info@nordicproaudio.com
Matched 4006A Stereo Pair
A complete stereo kit with two carefully factory-matched phantom powered 4006A Omnidirectional Condenser Microphones. The kit includes mics, windscreens, boom, holders, clips, and much more.
- Modularity – interchangable capsules and preamplifiers
- Up to 120 dB dynamic range
- RF rejection between >60 and >40 dB
- Linear frequency response
- High SPL
- Superior gain before feedback
Even though the standard tolerances on our recording mics are already extremely low, a stereo match is even closer. These specially selected 4006A Omnidirectional Microphones are matched within ±0.5 dB on both frequency response and sensitivity.
For reference stereo recording, there is no better choice than a 4006A Omnidirectional Microphone. These omnidirectional condenser microphones are linear and true in character. They come as a hand-matched pair that offers the truest capture of stereo sound available.
The 4006 Omnidirectional Microphone Capsule offers total transparency in any recording situation. It picks up incredible detail and depth of sound. The definition of its high-frequency characteristics across a wide range of instruments is impressive. It offers natural sound, high sensitivity, low noise-floor and linear frequency response from 10 to 20 kHz (±2 dB).
The 4006A Omnidirectional Microphone is a flexible solution. Engineers, broadcasters and musicians alike can achieve clean, natural and precise sound reproduction. This mic is ideal for A-B stereo pairs for symphonic concert hall recordings. It also excels on vocals, for close-miking all types of instruments and as an outdoor interview microphone.
A selection of accessories is available, including acoustic pressure equalizers, a nose cone and interchangeable protection grids. These accessories can acoustically transform the mic. By changing grids, it is possible to gain several unique frequency responses and directional characteristics from the mic.
Furthermore, these accessories will not produce any phase shift, noise or distortion that would otherwise be introduced by an electrical filter.
- 2x DPA 4006A Omnidirectional Condenser Microphones
- 6x Acoustic Pressure Equalizers
- 2x Free-Field Grids
- 2x Close-Miking Grids
- 2x Diffuse-Field Grids
- 2x DPA Microphone Clips
- 2x DPA Nose Cones
- 1x DPA Stereo Boom
- 2x Foam Windscreens
- 2x DPA Microphone Holders
| Directional Pattern: | Omnidirectional |
|---|---|
| Principle of operation: | Pressure gradient |
| Cartridge type: | Pre-polarized condenser |
| Frequency response: | 10 Hz - 20 kHz |
| Dynamic range: | Typ. 124 dB |
| Effective frequency range ±2 dB: | 10 Hz - 20 kHz |
| Sensitivity, nominal, ±2 dB at 250 Hz: | 40 mV/Pa; -28 dB re. 1 V/Pa |
| Equivalent noise level, A-weighted: | Typ. 15 dB(A) re. 20 µPa (max. 17 dB(A)) |
| Equivalent noise level, ITU-R BS.468-4: | Typ. 27 dB (max. 29 dB) |
| Distortion, THD < 1%: | 136 dB SPL RMS, 139 dB SPL peak |
| Max. SPL, THD 10%: | 146 dB SPL peak |
| Switchable attenuator, filters etc.: | 0 dB / -20 dB |
| Minimum load impedance: | 2 kΩ |
| Rated output impedance: | 200 Ω |
| Cable drive capability: | 100 m (328 ft) |
| Output balance principle: | Impedance balancing with Active Drive |
| Common mode rejection ratio (CMRR): | > 60 dB |
| Power supply (for full performance): | P48 (Phantom Power) |
| Current consumption: | 2.8 mA |
| Maximum output voltage, RMS: | 8.0 V |
| Polarity: | +V at pin 2 for positive sound pressure |
| Matching tolerance (frequency response and sensitivity): | ±0.5 dB |
| Phase deviation for kit: | < 5° |
| Weight: | 163 g (5.7 oz) |
| Microphone diameter: | 16 - 19 mm (0.6 - 0.75 in) |
| Capsule diameter: | 16 mm (0.6 in) |
| Microphone length: | 170 mm (6.7 in) |
| Temperature range: | -40°C to 45°C (-40°F to 113°F) |
| Relative humidity (RH): | Up to 90% |